Reaching for a new one: Can polyethylene thread replace spandex
Scientists at the Massachusetts Institute of Technology (MIT) have developed an elastic thread made of compatible varieties of polyethylene. In the laboratory, the material has withstood ten cycles of remelting and re-molding without a noticeable decrease in strength. According to the authors, the development can simplify the processing of sportswear and other items in which spandex is combined with polyester or nylon today. However, a successful experiment with pure yarn does not mean that the technology is ready for mass production of clothing. What other tests the material must undergo and how it will change the fashion industry are in the "Izvestia" material.
What is the discovery of MIT scientists?
Modern elastic fabrics are usually made from several materials. Spandex, which is a polyurethane fiber, is responsible for stretchability, but has a relatively low strength. Therefore, it is combined with more resistant fibers, primarily polyester or nylon. The resulting fabric tolerates loads well, but after the end of its service life, it is difficult and expensive to divide it into its original components.
MIT engineers proposed replacing chemically different materials with two types of polyethylene. They chose a soft, stretchable polyethylene copolymer for the core, and a more rigid polyethylene fiber for the outer part. The latter is spirally wound onto the core and gives the thread additional strength. The initial granules are melted at about 177 degrees, after which they are passed through extruders and stretched into thin fibers. The authors compare this process to the operation of a spaghetti machine.
Both parts of the thread belong to the same chemical family, so they do not need to be separated before processing. The used material can be melted and then molded back into fiber or used to make other products, such as buttons, buckles, or plastic parts. The researchers believe that the technology can be scaled up to the production of industrial coils.
The fundamental novelty is in the production of an elastic thread from a polymer that is not usually classified as elastic materials, explained "Izvestia" Professor of the Department of Chemical Technology named after Professor A.A. Kharkharov St. Petersburg State University of Industrial Technology and Design Anna Mikhailovskaya.
— This thread can be considered as a bicomponent, which has a core and a shell. They usually consist of different polymers, each of which gives the material certain properties. Polyethylene of the same chemical nature, but with different physical properties, is used here. One component provides elasticity, and the second component is responsible for strength," the expert said.
""Olga Stadnik, Head of Research and consulting at EcoTechnology, also draws attention to the "single-family" composition of the material. According to her, the combination of elasticity and strength is achieved not by crosslinking agents or additional polymers, but by controlling the molecular architecture of polyethylene.
— The soft copolymer in the center behaves like an elastic band, and the harder material performs the function of a durable shell. Traditional elastic fabrics are made of polymers that do not combine well during processing, including due to different melting points. The new material partially removes this problem," she explained.
What kind of clothes can be made from a new thread
The developers compared the polyethylene thread with a commercial polyester and spandex material. The new sample demonstrated comparable stretchability, and surpassed the thread used for comparison in terms of maximum load before breaking. MIT believes that the material can be woven into lightweight and elastic fabrics in the future.
However, it is premature to talk about a full-fledged replacement of spandex. Anna Mikhailovskaya recalled that polyurethane fiber can increase in length by five to seven times, and after removing the load, return to its original dimensions. Whether the new material can withstand repeated deformations of this scale throughout the life of the product remains to be seen.
— A thread is not a finished product yet. It is necessary to produce fabric or knitwear from it, and it is not yet clear how it will behave during weaving, knitting and subsequent operation. In addition, along with polyurethane, cotton or viscose is usually used for linen, which absorb moisture and provide tactile comfort. Polyethylene is a hydrophobic material and does not possess such properties," the specialist noted.
In her opinion, one of the first applications may be not clothes and underwear, but non-woven materials for medicine, the food industry and construction. Polyethylene products can be lightweight, durable, chemically inert, resistant to moisture and at the same time breathable due to the structure of the material.
Coloring remains an additional problem. Spandex and many traditional fibers can be dyed in aqueous solutions, whereas polyethylene practically does not interact with such dyes. The pigment will have to be injected directly into the melt before forming the filament. It is still unknown how it will affect the elasticity, strength and quality of secondary raw materials after several refinements.
Polyethylene itself is also insufficiently resistant to prolonged exposure to ultraviolet radiation. If the material is intended to be used for swimwear or sportswear, light stabilizers will have to be added to its composition. This will increase the service life of the item, but at the same time complicate the composition of the raw material and require checking its suitability for recycling.
What did the experiment with the new thread show?
To test the recyclability, the scientists made a spool of thread, melted the material, and molded it back into fiber. This procedure was repeated ten times, measuring the mechanical characteristics after each cycle. The recycled samples retained strength comparable to the original material. At the same time, the MIT report clarifies that a new durable outer thread was obtained from recycled polyethylene, which could then be wound onto a newly manufactured elastic core. Therefore, it would be incorrect to claim that the entire structure was transformed ten times into exactly the same elastic thread without changes.
According to Olga Stadnik, ten cycles without significant loss of strength is a strong laboratory result: not all polymers used even for packaging and household products demonstrate such stability. But the test was conducted under controlled conditions and with clean material, whereas the actual waste is almost always contaminated.
— It is necessary to check how the material will behave after buttons, zippers, labels and foreign sewing threads get into it. It is important to study the change in the molecular weight distribution: strength may remain, but breakage may increase with repeated spinning. A separate question is whether dyes and additives will degrade when heated to form by—products," the expert emphasized.
For the processor, not only the number of laboratory cycles is important, but also the quality of the final product. Even if, after re-melting, the material can no longer be turned into elastic clothing, it is theoretically possible to obtain a film or other polyethylene product from it. Such a scheme will allow the polymer to be returned to economic circulation, but this will no longer be a closed cycle of "clothes into clothes", but processing with a decrease in the quality and value of products.
Why is new material alone not enough?
The problem of textile waste has a global scale. According to estimates by the European Environment Agency, in 2020, about 6.95 million tons of such waste were generated in the EU countries — about 16 kg per person. Only 4.4 kg per person was collected separately for reuse and recycling, while 11.6 kg ended up in mixed municipal waste. The average rate of individual textile collection in European countries was only about 12%.
The mixed composition of things remains one of the main technological obstacles. To process the polyester and spandex material, the components must be chemically separated. As explained by Anna Mikhailovskaya, hydrolysis or glycolysis can form a complex mixture of terephthalic acid, amines and polyols, which then also needs to be separated and purified.
— When a product consists of polymers of different chemical nature, processing involves several reactions or leads to a mixture of target products. Its separation is very laborious. If the material is made only on the basis of polyethylene, the process is greatly simplified," she said.
Theoretically, not only fabric can be made from polyethylene materials, but also sewing threads, zippers, buttons and fasteners. Then the thing can be crushed and melted whole. However, the monomaterial composition alone does not guarantee recycling.
"Innovation answers "can it be recycled?" but "will it be recycled?" is a much more difficult question. Polyethylene clothing that gets into the flow of cotton or polyester fabrics can contaminate secondary raw materials. Therefore, most likely, separate collection and sorting will still be required," the expert noted.
Labeling and automated sorting may be necessary to recognize the composition of items. Such technologies are already undergoing industrial testing. As the Associated Press reported, an automated system installed in China is capable of sorting up to 100 kg of clothes in two to three minutes, whereas it takes about four hours for a person to do this. However, even accurate recognition of the material does not solve the issue of economics: a separate stream appears only when there is a lot of waste, and there is a stable demand for the raw materials obtained.
The full environmental impact of the new thread has also yet to be assessed. This will require a life cycle analysis: the amount of energy during manufacture and remelting, the carbon footprint, water consumption, product life, and the likelihood of microplastic formation.
Textile recycling in Russia
In Russia, the infrastructure for clothing recycling is expanding, although it still covers only a small part of the waste generated. According to the Russian Environmental Operator, the number of enterprises in the textile recycling register increased from four at the end of 2024 to 22 in 2026, and their total declared capacity increased from about 70 thousand to 274.2 thousand tons per year. One of the largest projects uses more than 5.5 thousand containers and produces regenerated yarn, work gloves and mittens from the collected raw materials.
However, a significant part of Russian processing is still based on the mechanical grinding of textiles, followed by the production of cleaning, insulation and other technical materials. To implement a full–fledged chain "polyethylene fiber – clothing - new fiber", separate capacities for sorting, washing, grinding, melting and re-spinning will be needed.
According to Olga Stadnik, the creation of such a system is not so much an insurmountable technical barrier as a matter of investment, standards and sufficient raw materials. If polyethylene clothing occupies a small market share, it may not be economically feasible to separate it into a separate stream. At the initial stage, a more realistic model could be controlled deliveries of workwear, medical or technical materials, which are purchased and collected by one organization after use.
The prospects for development will also depend on whether manufacturers manage to keep the composition of the finished product simple. Adding cotton for comfort, elastane for greater stretchability, complex dyes, or incompatible fittings will turn it back into a multicomponent product and partially deprive the technology of its main advantage.
Переведено сервисом «Яндекс Переводчик»